Skip to content
Align by NETLCO
Sign in

What you need

What you need to measure

Nothing to download. The analysis runs in the page, no audio leaves your browser, and no file you open is kept by us. While Align is in testing, check it against an instrument you trust before relying on it: measure the same system at the same moment with both, and compare the traces, not the verdicts.

A computer with Chrome or Edge
They let a page ask an audio interface for its channels; Firefox and Safari do not. Any browser opens a file.
An interface and a measurement microphone
The free RTA and SPL meter need one microphone. Pro's transfer function needs two channels, the reference and the microphone. Up to 16 inputs, two from each of up to 8 devices, chosen in I-O Config. With Pro, run the channel check before trusting any of them: in five seconds it says whether the browser keeps them apart.
A loopback cable, if you have one
Into input 1 it gives Pro's delay finder an absolute delay. Without one, Align's own output is the reference and the delay is relative, as a browser's output latency estimate varies and can read zero.
Or, with Pro, an exported trace
Export the trace as ASCII text, then File, Import trace in the instrument. Any browser, no interface. Importing a trace comes with Pro.
With nothing to hand
With Pro, File, Load the worked example opens the EQ screen on a generated trace, so each screen that works from a trace has one.

Interfaces and measurement microphones

Common choices, none ranked: each group runs A to Z by maker. Each figure on a card is its maker's own, read on 22 and 23 October 2026 from the maker's page linked on the card. The notes on choosing and each line marked In Align are ours. No maker pays for a place here.

When choosing

  • At concert level, pick a microphone with a maximum SPL of at least 135 dB SPL, preferably 140 dB SPL, as music's peaks run 30 to 35 dB over its average A‑weighted level. Six here are rated to 140 dB SPL or more, all on XLR, the two G2s on 48 V phantom power only. The TM1 Plus and the M50 are among them on a maximum with no distortion figure named, and at 1% distortion Audix gives the TM1 Plus 130 dB SPL, under 135 dB SPL. The next note checks each against the interfaces.
  • To check a microphone against an interface, multiply its mV/Pa by 200, as 140 dB SPL is 200 pascals: that is its output in millivolts at 140 dB SPL, which the interface's maximum mic input has to take. A low sensitivity, typically 6 to 15 mV/Pa, keeps that output down, as a more sensitive one can overload the interface even at its lowest gain. The cases below work out the six at each maker's sensitivity, and at the top of its tolerance where the maker gives one, with the interfaces here whose maximum takes each output. Plan for the top, as one unit can sit anywhere within its tolerance. Behringer's pages give no maximum mic input.
    • +3.8 dBu, the TM1 Plus and EMX‑7150 at 6 mV/Pa: every interface here with a figure. At Audix's +3 dB the TM1 Plus gives +6.8 dBu, still under every one.
    • +8.2 dBu, the M23 G2 and M30 G2 at 10 mV/Pa: every interface here with a figure, the Babyface Pro FS with its pad. At Earthworks' +2 dB they give +10.2 dBu, past the MOTU M2 and M4.
    • +14.3 dBu, the M2211 at 20 mV/Pa: the Audient and Focusrite cards, and the Babyface Pro FS with its pad. At NTi's +3 dB it gives +17.3 dBu, which only the Babyface Pro FS with its pad takes.
    • +18.9 dBu, the M50 at 34 mV/Pa: only the Babyface Pro FS with its pad, 0.1 dB under its +19 dBu. Earthworks' page also gives −29 dBV/Pa, which works out to +19.2 dBu, over it, and its user guide calls the 34 mV/Pa typical, so an M50 more than 0.1 dB hotter than typical overloads it.
    • With four microphones on one interface: the Audient and Focusrite cards with four or more mic inputs take the TM1 Plus, the EMX‑7150 and both G2s, at the tops of their tolerances too, and the M2211 at NTi's figure but not at its top. None of them takes the M50, and Behringer's UMC404HD and UMC1820 give no maximum.
  • Makers state maximum SPL at 1% or 3% distortion, at full scale, or with no distortion figure named. The first note's 135 dB SPL names no distortion, so set each card's maximum against it as its maker states it.
  • Keep input 1 or 2 for a loopback cable: Align then reads an absolute delay, and the IR sweep needs the cable there. Without one, Align's own output is the reference and the delay is relative.
  • Plug the interface straight into the computer: a USB hub can run short of power for an interface that also powers microphones.
  • Load each microphone's calibration file on its input: I‑O Config, Load a calibration file.
  • For dB SPL, use a sound level calibrator, Class 2 or better, with its certification documentation. In Align, open SPL and press Connect in the control bar. Put the calibrator on the microphone and, with two or more inputs open, choose that microphone's input under Input. Type the calibrator's level in "What your reference meter reads" and press Calibrate. Repeat for each microphone you will read in dB SPL, then choose under Input the one the meter should read.

Interfaces with two mic inputs

  • Audient EVO 4

    • Two analogue inputs, each with 48 V phantom power
    • Maximum mic input +16 dBu
    • USB 2.0, USB‑C

    Audient's specifications

  • Behringer UMC202HD

    • Two Midas mic inputs with 48 V phantom power
    • 24‑bit, 192 kHz, USB 2.0

    In Align: Behringer's page gives no maximum mic input, so watch the input meter's Max and its clip count at the loudest level you measure.

    Behringer's page

  • Focusrite Scarlett 2i2 4th Gen

    • Two mic inputs with phantom power
    • Maximum mic input +16 dBu
    • 24‑bit, 192 kHz, USB‑C, USB 2.0
    • Powered from USB

    Focusrite's page

  • MOTU M2

    • Two mic inputs, each with its own 48 V phantom power
    • Maximum mic input +10 dBu at minimum gain
    • 44.1 to 192 kHz, USB‑C, USB 2.0
    • USB audio class compliant

    MOTU's specifications

  • MOTU M4

    • Two mic inputs, each with its own 48 V phantom power, and two line inputs
    • Maximum mic input +10 dBu at minimum gain
    • 44.1 to 192 kHz, USB‑C, USB 2.0
    • USB audio class compliant

    MOTU's specifications

  • RME Babyface Pro FS

    • Two XLR mic inputs, each with its own 48 V phantom power
    • Maximum mic input +8 dBu at 0 dB gain, +19 dBu with the pad
    • 28 to 200 kHz, USB 2.0

    RME's page

  • Universal Audio Volt 2 Gen 2

    • Two mic inputs, each with its own 48 V phantom power
    • Maximum mic input +14 dBu
    • 32‑bit, 44.1 to 192 kHz, USB‑C, USB 2.0

    Universal Audio's page

Interfaces with four or more mic inputs

In Align: Align takes two inputs from each device the computer lists, sixteen in all at most, so it reaches more than two of these only where the driver lists the inputs in pairs; each card says what its driver does on Windows. A Mac lists an interface as one device, so there Align reaches two of its inputs.

  • Audient EVO 8

    • Four analogue inputs, each with 48 V phantom power
    • Maximum mic input +16 dBu
    • USB 2.0, USB‑C
    • Phantom power on two channels only from a USB‑A computer

    In Align: Install Audient's EVO driver first on Windows. It then lists inputs 1 and 2 as one device, 3 and 4 as another and the loopback, inputs 5 and 6, as a third; choose the others in I‑O Config, then Connect interface, or Reconnect if already measuring, and Align opens them: four microphones and the loopback. Each XLR microphone here takes phantom power, so a third or fourth needs the EVO 8 on a USB‑C to C connection.

    Audient's specificationsAudient's overview

  • Audient EVO 16

    • Eight mic inputs, each with 48 V phantom power
    • Maximum mic input +16 dBu
    • 24 inputs and 24 outputs in all, ADAT and SPDIF among them

    In Align: On Windows Audient's driver lists the inputs in pairs, 1 and 2, 3 and 4 and so on, and Align opens up to eight pairs, chosen in I‑O Config: sixteen microphones, or fifteen and a loopback cable.

    Audient's specificationsAudient's overview

  • Behringer UMC404HD

    • Four Midas mic inputs, each with 48 V phantom power
    • 24‑bit, 192 kHz, USB 2.0

    In Align: On Windows its driver lists IN 1‑2 and IN 3‑4; choose IN 3‑4 in I‑O Config, then Connect interface, or Reconnect if already measuring, and Align opens both: four microphones, or three and a loopback cable. Behringer's page gives no maximum mic input, so watch the input meter's Max and its clip count at the loudest level you measure.

    Behringer's page

  • Behringer UMC1820

    • Eight Midas mic inputs with 48 V phantom power
    • 24‑bit, 96 kHz, USB 2.0
    • 18 inputs and 20 outputs in all

    In Align: Behringer's page does not say how its Windows driver lists the inputs, so Align may reach only the first two. Nor does it give a maximum mic input, so watch the input meter's Max and its clip count at the loudest level you measure.

    Behringer's page

  • Focusrite Scarlett 18i16 4th Gen

    • Four mic inputs, each with its own phantom power
    • Maximum mic input +16 dBu
    • 24‑bit, 192 kHz, USB‑C, USB 2.0
    • Powered from USB, or an optional 15 W supply

    In Align: On Windows Focusrite's driver gives a browser, which does not use ASIO, a single recording device of two inputs until you expose more pairs in Focusrite Notifier, Expose/⁠Hide Windows Channels; Align then opens up to eight pairs, chosen in I‑O Config.

    Focusrite's page

  • Focusrite Scarlett 18i20 4th Gen

    • Eight mic inputs, each with its own phantom power
    • Maximum mic input +16 dBu
    • 24‑bit, 192 kHz, USB‑C, USB 2.0
    • Its own 30 W supply, not USB power

    In Align: On Windows Focusrite's driver gives a browser, which does not use ASIO, a single recording device of two inputs until you expose more pairs in Focusrite Notifier, Expose/⁠Hide Windows Channels; Align then opens up to eight pairs, chosen in I‑O Config.

    Focusrite's page

Measurement microphones on XLR, through an interface

  • Audix TM1 Plus

    • 6 mV/Pa
    • 130 dB SPL at 1% distortion, 140 dB SPL maximum
    • 24 to 48 V phantom power
    • Calibration data included

    Audix's data sheet (PDF)

  • Behringer ECM8000

    • 20 Hz to 20 kHz in its guide; its page's text says 15 Hz to 20 kHz
    • Omnidirectional
    • 15 to 48 V phantom power
    • Clip, stand adapter and case included
    • Downloads, Firmware: a zip, its .rtf named "Generic ECM8000 Calibration File"

    In Align: Behringer gives no sensitivity in mV/Pa. Its calibration file is one table for the model, in an .rtf and an .ods: copy the table from the .ods into a .txt to load it in I‑O Config. Until a file is loaded, Align reads the microphone as flat.

    Behringer's pageBehringer's Quick Start Guide (PDF)

  • beyerdynamic MM 1

    • 15 mV/Pa
    • 122 dB SPL at 1% distortion
    • 12 to 48 V phantom power
    • Individual compensation curves, 0° and 90°, on request once registered

    beyerdynamic's data sheet (PDF)

  • Dayton Audio EMM-6

    • 10 mV/Pa
    • 127 dB SPL at 1% distortion
    • 15 to 48 V phantom power
    • Individually calibrated, its file from Dayton Audio

    Dayton Audio's page

  • dbx RTA-M

    • −63 dB re 1 V/microbar
    • 9 to 52 V phantom power
    • Clip and case included

    In Align: dbx's −63 dB is about 7 mV/Pa, as a microbar is a tenth of a pascal. Its page names no calibration file, so Align reads it as flat until you load one.

    dbx's page

  • Earthworks M23 G2

    • 10 mV/Pa
    • 140 dB SPL at 3% distortion on 48 V phantom power
    • 133 dB SPL at 3% distortion on 12 V phantom power
    • Flat within 1 dB from 5 Hz to 23 kHz
    • Its own calibration chart: its response, and its sensitivity at 1 kHz and 250 Hz

    In Align: Earthworks' G2 page names a calibration chart for it, not a file, and its calibration file request form does not say whether it serves the G2, so ask Earthworks through that form before counting on one. Until a file is loaded, Align reads it as flat.

    Earthworks' pageEarthworks' user guide (PDF)Earthworks' calibration file form

  • Earthworks M30 G2

    • 10 mV/Pa
    • 140 dB SPL at 3% distortion on 48 V phantom power
    • 133 dB SPL at 3% distortion on 12 V phantom power
    • Flat within 1 dB from 5 Hz to 30 kHz
    • Its own calibration chart: its response, and its sensitivity at 1 kHz and 250 Hz

    In Align: Earthworks' G2 page names a calibration chart for it, not a file, and its calibration file request form does not say whether it serves the G2, so ask Earthworks through that form before counting on one. Until a file is loaded, Align reads it as flat.

    Earthworks' pageEarthworks' user guide (PDF)Earthworks' calibration file form

  • Earthworks M50

    • 34 mV/Pa
    • 140 dB SPL maximum
    • 24 to 48 V phantom power
    • 3 Hz to 50 kHz
    • Its own printed response chart, and a calibration file of its own, free once registered

    Earthworks' pageEarthworks' user guide (PDF)

  • iSEMcon EMX-7150

    • 6 mV/Pa
    • Over 140 dB SPL at 3% distortion, typically 145 to 146 dB SPL
    • 12 to 52 V phantom power
    • Its individual calibration data included, as files and a chart

    iSEMcon's data sheet (PDF)

  • NTi Audio M2211

    • 20 mV/Pa
    • 144 dB SPL at 3% distortion
    • 48 V phantom power
    • Its individual response as an Excel file, free on request once registered

    In Align: Align loads text, not a spreadsheet: copy the table into a .txt to load it in I‑O Config.

    NTi Audio's PDF, pages 6 and 7

  • PreSonus PRM1

    • 14 mV/Pa
    • 132 dB SPL at 1% distortion
    • 9 to 52 V phantom power
    • Clip, windscreen and hard case included

    In Align: Its page names no calibration file, so Align reads it as flat until you load one.

    PreSonus' page

Measurement microphones on USB, with no interface

In Align: Each is one microphone with no input beside it for a loopback: Align's own output is the reference, so the delay is relative, and the IR sweep, which needs a loopback, does not run. Align opens up to eight at once, each on its own clock, so over a long measurement their delays can drift apart; an interface's inputs share its clock.

  • Dayton Audio UMM-6

    • 10 mV/Pa
    • 127 dB SPL at 1% distortion
    • USB B socket
    • Individually calibrated, its file from Dayton Audio

    Dayton Audio's page

  • miniDSP UMIK-1

    • 133 dB SPL at 1% distortion, 0 dB gain
    • 24‑bit at 48 kHz
    • No driver needed on Windows, Mac or Linux
    • A unique calibration file by serial number, and a 90° one

    miniDSP's page

  • miniDSP UMIK-2

    • 125 dB SPL at full scale
    • 32‑bit, 44.1 to 192 kHz
    • No driver needed on a Mac, Linux or Android; on Windows miniDSP's driver must be installed, from User Downloads on its website, signed in
    • A unique calibration file by serial number, and a 90° one

    In Align: On Windows Align reads it as a Windows recording device, as Chrome does not use ASIO.

    miniDSP's pageminiDSP's user manual (PDF)miniDSP's User Downloads

Start with the free RTA and SPL meter.

Both open in your browser with no account, and no audio leaves it. To measure through an audio interface, use Chrome or Edge on a computer. Pro adds the transfer function, EQ and every other tool.